Easy Way to Sight In Your Rifle

This bore sighter was obviously sighted in at the factory. Most of them have to be adjusted by turning the two hex screws on the side of the bore sighter itself. Place it in a drill, turn it making small adjustments till the dot stays in one spot then place it in the barrel of the gun you want to zero in.

Can u show the second setting and how u did w

At what distance are you shooting at ?

Get on paper is a huge advantage in zeroing your optic.

Does it able for 45-70?

THANK YOU.

I've seen one step that's seems to work well.
If you're around 2 inches low at 25 yards you'll be close at 100yards

Had one. Sent it back. Would not stay consistent. Not a fan.

I bought a cheap laser key ring from a dollar store took the key ring off and popped it in the drum and lined up my scope and I’m not showing off but I never miss the bull’s eye

Pos temu

they are not accurate, far better one's out there.
like any scope shoot adjust to bullet hole job done

Actually I’ve heard the opposite, that the cartridge style devices aren’t “underwhelming” in fact they are generally more accurate and consistent than muzzle mounted ones because they sit in the rifle’s chamber and align with the bore axis, while muzzle units depend on how well they fit the muzzle or crown, which can introduce slight misalignment, especially on rifles with flash hiders like an AR-15.

Cvlife bore sighter is cheaper and does the same !

No better than one that goes in the chamber.

What’s your rifle name bro?

Mistake you made is you should have tightened the sighter once In the bore. It should snug up the adapter enough to make it equally centered in the bore. Yours Was lose.

That's a hellava lot adjustment for a tool that was supposed to get you close..wtf…I've never had to do that many clicks.

A standard level, a Segway leveler, and within a couple shots I'm zeroed…

And if you're at 25yrds, put your crosshairs about an inch above the dot…if you're planning on long distance hunting.

Just ordered one today, not this one but got a rds coming tomorrow and wanted a boresight to help me out so reading up on em, thanks for the vid, commenters are unsung heroes too! 😂🤘

I tell you I have a nightmare of a time sighting in offset dots (45 and top
Dot) my cheapo bore sight from Amazon got me exactly where I needed for be with my laser and offsets. Don't really need this for a primary optic tho.

So you lined it up with green laser but it was not sighted correctly? NO BUENO

Few bucks on eBay 🤙

I rotate the lazer once it's in the bore. Sometimes it makes a circle. Locate the lazer at 6 o'clock and start there.

Make sure you twist it and watch the laser dot. Does it move in a circle? That's not good

How many yards should I do this at ?

These are only really good to get horizontal alignment of the scope in close enough alignment with the barrel.

These are pretty much useless to try to adjust the vertical zero due to it being a laser and only point in a straight line and can't account for bullet drop the further out you go, so you have to adjust vertical alignment completely manually depending on what range you're setting for zero.

Works very well!! Love mine

👌💯

The laser bore sighted that go in the chamber are just not strong enough the case is to small to put out a good enough t laser these are not only more powerful but universal

I’ve had an older version of this for about two years, and it has always done a great job for me. I love it. The various tips allow me to bore site all the firearms they have, and the batteries don’t burn out in a big hurry.

Señor cuantas yarda hay de donde está el rifle hacia la diana de tiro 25 o 50 yarda

Curious, do you not measure for Height Over Bore at the closer distance and then put reticle on that. Obviously you are just getting on paper, but curious if you factor for that if in close before shooting out at distance?

Does this work on firearms with only iron sights?

I have NEVER found one worth the price.

there is no way in hell the specific caliber one performs "underwhelming". I would much rather have something that is caliber specific than one you just stick in the end of the barrel and up its concentric.

I got it I hope it works on air gun

Can maybe put bore sighter back into the barrel and make adjustments to the shot group.

So is your sight supposed to be above the bore sight laser dot or is it supposed to be directly on the dot?

Hey guys laser bore sights arnt the best but here look at this laser bore sight this will be the best bc yk they sponsored me

How can a laser, inside the bore under perform? Light goes in the bore and out. Doesn’t get much straighter than that. Quit trying to sell shit that doesn’t work, jmo!