Review & Install of the Magpul AFG2 Angled Fore Grip

And he fast forwarded the install part 🙄

It’s in the mail for my 18” ruger ar 556 as we speak. I’m swapping out the mp vertical for one of these!

Does it require piticanny to mount to or can I mount directly to cage?

I hate you

Not to be negative but you edited out the main part of why people went to this. I understand its simple, but ya gotta show each step, even when its simple.

Thanks for the video. I watched the video after installing the Angles Fore Grip because I had no idea what the little piece was for. Thanks for showing me!

M416

I can’t get this to fit my scar. Rail seems too wide. Any thoughts???

Attn everyone. Some picatinny rails follow 1913 specs, some do not. If it doesn’t seem like it will fit, it will. Just loosen screws or mallet it on. As long as your rail isn’t made of Chinese plastic, you will not harm your rail.
Also, thanks to all who still run picatinny. Fuck mlok. And if you have keymod, just remember you picked HD DVD when Blu-ray already won.

Hey my afg2 didn’t come with the screw in the middle. Must’ve gotten past quality control but what size screw is that. Can i find it at lowe’s ?

Trash ass video and glad I fast fwded to find out you don’t actually show the installation

My AR15 is keymod, if I were to buy a picatinny for this specific grip, how many slots would be needed?

Your video says install, yet you didnt show us the install. Am I the only one that feels this way?

Ers how u do it. Voila. Done…???

Does this go with mlock?

Hey that looks like a bong…. oh wait that's a dirty powder dumper. Or as I like to call it " bang Clapper "

You didn't even show the actual installation.., shitty video

Alright hi uys i figured it out… You have to pop it on to the picatinny Rail. Gonna have to use some pressure and it makes it easier if you have everything loosened up… Get one side of the rail lined up, apply preasure and the other side will pop on. After that just use a rubber malet to get it to your perfered position… This was way harder then it should have been… Unlike most of you i got this from a friend in a plastic bag, i didn't have instructions.

Best grip in PubG mobile

thanks for sharing. very good. but did you need a Angled Foregrip Front Grip &Adjustable Red Dot Laser Sight for Picatinny Rail ? come here http://souforce-hunting.com/c/grips-0394

Level 2 cok

Just put a cheapo airsoft one (angled foregrip) on my very first AR build…tuned in here to see how it's done. Thanks!

Who will come after pubg…?

Look out all the fat he has. Plus his is belly fat is not in proportion to the size of his arms

I just purchased one of these angled grips and have a few tips which were omitted in this video. 1) whether or not you want to exchange the finger shelf, do yourself a favor and loosen the three hex head screw which hold the grip together. Failure to do this simple step makes the grip assemble very difficult to slide onto the rail. In fact you may resort to using a rubber mallet to move it along the rail. 2) If you disassemble the grip understand that it doesn't pull apart into two halves. It has a couple of locks and it is "hinged". The best way to disassemble it is to open it like a book. Reassembly is the same way: connect the two halves at the bottom and then fold the grip together like you are closing a book. Like everything from MagPul this item is well made with nice molding and no sharp edges.

How do u fit it on the rail? Can't get mine over the picatinney. Won't separate, won't fit. Palmetto upper

How are you going to shoulder it with your arm locked into that brace , if your going to use the brace with your arm in it why install the angle forearm grip in the first place .

The cheap eBay foregrip with the thumb rest is vastly more comfortable, ergonomic and cheaper. I've had mine on for a while, even through many running and gunning exercises, and it has been flawless. Also, it has a cubby hole to store extra batteries, allen wrench or whatever small items you may need. If you want extra piece of mind add some blue locktite to the screws. I've had other Magpul items but only like very few of them. In particularly their AFG. But hey, that's just this Marines POV.

Took you longer to get it out of the box then it did to get it on, yet you had to edit that part out. Lol. Yeah sure buddy.

SEEMS YOU OMITTED THE ACTUAL APPLICATION…WTF?

Would this fit the tippmann tmc

How is this type of stock called? I really need this in my life. Greetings from Europe

Just so you know putting a forward grip on a pistol is illegal and turns it into an any other weapon just saying might want to take that off before they find out

mine doesent fit on my rail

Pistol my dick, poor man sbr

What manufacture are you running on your lower receiver? And what's your barrel length? Sweet looking 300 Blackout!

Very informative video. Easy to follow, great job

dang…i shouldn't have fwd your vid, because you explained it..lol….im going cucu here..

just figured it out, it seems as though it replaces the plastic notch on the grip making it a smooth out grip…

thanx, great presentation, though 1 question, whats the little (plastic square) that came with the fore grip used for? thanx again.