Everyone asks where I find AR-15 stuff in stock or where I order from, so here you are:
———————————————————————————–
My buddy Dale from Little Crow Gunworks demonstrates how to properly check headspace on an AR-15 barrel that has been installed. Dale is the inventor or the R.P.P Roll Pin Pusher AR-15 Tool as well as the W.F.T World’s Finest Trimmer. He is extremely knowledgeable and was very nice to have taken the time to demonstrate this! Thanks again, Dale! Check out his website, and tell him I sent ya!
For 20% off of your order from use promo code: nsz85
Thank you for watching and please subscribe for future videos!
Note to readers: Please click the share buttons above or below. Forward this article to your email lists. Crosspost on your blog site, social media, internet forums. etc.
Would be helpful to see what happens in each case if the parts fail.
Thanks for the great video!
OMFG….THOS GUY IS WAAAY TO MELLOW…….STONED??
High end boron coated BCG. Spikes tactical HBAR. I should be good. Thanks much for the reassurance.
OK, now we know that the HS is ok. What do we do if it was not OK?
Thanks.
Incorrect Headspace.. The space between your penis head and her mouth when it should just be in her mouth.
You don’t formally become a gunsmith until you’re well into your 50s, have a gut and white hair. Before that your opinion on guns does not matter
I noticed that some people are grinding down the gauges to allow room for the ejector without removing it. Is there any risk to doing this?
Thank you.
What about the "field" gage?
I've started a pcc 9mm build and I've read a few places you don't really need to worry about head spacing sense its a different kind of bcg is that true?
I hope the viewers noticed what I did? You are only one of maybe 2 people I would allow to service/modify my firearms. You have a very gentle and patient disposition while handling and servicing the firearm. A lot of respect to you my good man!
I'm having problems with mine when I load magazine slap button for release and she's not closing completely and result's in misfire
And how do you adjust it if needed?
I like the method you used to put the ejector back in. I was about to buy a $60 dollar tool on Brownells web site. Thanks for the lesson.
Great video.
When you realize AR15’s don’t need the headspace checked
So what I want to know is if the head space is to much what needs to he done to correct it?
👍⚡️👍
Bilt quite a few seems like if everything is intolerance for mill spec really is not necessary to head space and unless shooting a wild caliber or handload high-performance ammunition
If you're going to demonstrate your procedure, have a better camera angle so we can actually see what you are doing. Most times your right hand was blocking the view.
Did he take the rod out of the barrel?
i know a gunsmith that went to colorado school of trades not online school. hes always maintained that you dont need to check the headspace on an ar as long as you arent using crap parts and you properly torque your barrel nut. hes built hundreds of rifles possibly 1000s
Why not use the bolt without the carrier, cutting off most of the neck of a spent round and holding it in the chamber by attaching it to a rod through the barrel. Then trying to insert the bolt and turn it by hand.??of course measuring the spent case dimensions prior to for reference, for acceptability.
Another great YouTube channel left for dead.
What an idiot. He proceeds to tell us how to check whether the headspace is good or not. Then he fails to tell us what to do if the headspace is not good. This is so typical of people who can't think past the obvious, and dig deeper into a concept: such as what to do if the headspace is not good! Didn't you think that you should tell us how to fix a problem headspace? I wouldn't send my firearm to that gunsmith if he offer to do the work for free.
OUTSTANDING explanation 🔫🇺🇸🔫🇺🇸🔫🇺🇸
should show one that fails …