Thanks for watching!
If you’d like to learn more check out this video from Geissele:
Note to readers: Please click the share buttons above or below. Forward this article to your email lists. Crosspost on your blog site, social media, internet forums. etc.
This spring is trash. The spring is very quiet but not reliable. Takes a lot of metal off the buffer tube. You will have to clean your buffer tube after 300 rounds.
“ basically the same “ ? Except you have to use their proprietary buffer and it cost 60.00 dollars, compared to a spinco spring for 20.00 dollars and you have a choice of different spring strengths and they allow for any mail spec buffer 🤔
But my main point is the super 42 just kicks ass it has h1-3 it is such a good system it will last 10 times longer than your standard quality car being spring and as soon as you racket you’re like oh wow this was worth 70 bucks for an H2 and then I continue to Byam I have three RN and he’s a mind systems that will work great with it and you know it’s super it’s almost like is it it’s very very quiet especially when you released your boat for shooting suppressed subsonic that’s where it really really shines you get zero twang and the twang sort of makes guns even if they’re quality firearms and Mason feel shitty so I invest in longevity in the parts that I buy for the most part and do some R and D and the R&D is it on like the centurion barrel they cross pendant at the top because of how low profile there gas block was and they also have a notch that corresponds to the perfect spot in the barrel for it to sit over the gas port and then obviously it has set screws for if you’re such a growing one but when you buy it with the system pinned it’s worked phenomenally and it’s got a .061 carbine gas is from which is crane spec it’s about .0615 and that’s my barrel but they say it’s around .061 and .062 is crane spec for an M4 so with the barrels I purchase I have to focus on quality ammo and is the system going to cycle it properly without a suppressor so I might have to buy a H one which I’m fine with it’s what 60 bucks and if the H one doesn’t work for you you can always buy a $20 tungsten weight and add it to it as the system allows you to do that to change weights out I assume you need a kit punch kit Jordan still gotta figure that one out
But for example right now as it sits it’s a $4000 set up easily and on going to be ordering the SPS when they are back in stock every is your fire can is not in stock but the SPS is gonna be my first 30 Cal can dance backwards compatible which is cool and it’s a little bit longer than the RC two but I might throw down my 55 sixes just to Yosi but inevitably I’ll either be getting another share fire or if my left dominant side does not like it give in with the gas busting charging handle from Radian and I do use optic risers I put you in a better situational like for your body your muscular skeletal situation system and you have situational awareness around you more so than you would if you were sunk into the optic lake and ACOG that at absolute if you understand what I’m saying plus if you are wearing armor and you sync down into the gun you can easily get hit in between your arm or you could get hit in the neck thoracic area that gets exposed is in your chest in the boat will zip through you do not want it to zip through from your chest downward angle doing God knows what so my tip is shoot your rifle like the way you shoot your handgun the same fucking way if that means get an optic riser and a cheek riser so be it they make a shit ton of them through the CTR stocks bunch for the B5 a few different not many but I have an APE defense 1 inch cheek riser for the B5 stock and run the unity Holographic setup right now with that and it’s on a Ris two also with a $500 barrel but at least it a lot more bar stock and it’s full auto rated for continuous full auto basically an SAW barrel with a cold as COM profile and probably can be used on the AR if it isn’t already it’s double chrome lined CHF centurion arms another if you were looking to do a GWOT built I’d recommend there’s also as well as for that set up definitely but they have a few other modern profiles and shit and they have them profiled and house their CHF out sourced as well as the Florida bar stock that they get you might as well use the best if you can so also if you’re going to buy a barrel and you know the ball carrier if it’s nitrated or not if it’s a Phosphated one definitely get it head spaced you want consistent pressures on that chamber people and manufacturers fucking overlook it like it’s a plague but there are different you know tolerant scabs in the fucking barrel extension not everyone is the exact same so and especially when you polish the barrel M4 extensions you need to find the right bolts and these companies have tons and tons they just have to maybe route through 30 or 40 and then they find the right ones and that’s why it cost 60 bucks because they had to go through a whole shit ton of bolts and use a Go gauge and a non-go gauge
Definitely one of the reasons I got it is the longevity and staying true to the design there’s so many odd contraptions and they’re priced a lot more like the GPSPS but I feel like it’s too much to fuck with too much to fill around with for an AR platform I just throw in one of these and change it up depending on what system I’m running and run them on every single AR that I have it made it my 10.3 a dream to shoot just using a H2 42 bufffer and spring I did hear that it does fit on the VolTr A5 they make one for it sort of I don’t know I might be miss information or some thing I didn’t get but I’ve seen people use them on that system but I have three of them and the tolerance definitely plays affecting boat bounce and shit like that or around the spring there in the buffer you know that the ring that you get from it getting chewed up by the detent and I had that on some mil spec sort of receivers and most companies don’t take into affect super tight tolerances and what not and that’s where you get your performance for example my radian model one there is zero movement and the receiver said it’s kept the super 42 in beautiful shape I built it myself it has a DDC buffer also from them but it’s a 10.5 and I threw a dev Gru 416R ss 10.5 barrel and the receiver set together it’s a match like perfect even though I bought my lower a year ago I recently bought the upper rail and I probably should’ve done that from the start but you know I have multiple upper sector of the lower on But anyway by 10 three that thing zero movement with the H2 as I was talking about and super flat shooting a bit heavy the MK4 rail with a Daniel CHF barrel but I am happy with the new radio model homes built thermal fitbarrel
I wanted to switch out my buffer and spring on my DDM4V7 just seems like my Daniel shoots a bit heavy so I’m thinking a good buffer and spring to calm that bolt down a bit I’m running the stock H buffer maybe a H2 anyone tried this spring and buffer on a DDM4V7 mid length gas system
Just installed a Super 42 as a replacement for the OEM spring and buffer on the S&W Volunteer XV. Pretty much to mitigate that buffer spring twang and it made a huge difference. Won’t know how it will run til I get out to the range but so far this was a great upgrade.
Just picked up their tube/buffer/spring kit with a H1 buffer for my 18” BCM. I’ve had a fixed A2 stock on it for years and it’s worked great but my son is getting interested in shooting and i need an adjustable stock for him.
You do know that your poster "I'm your Huckleberry" is the term used in the mid 1800's for gays. Not sure if you are intendingt to out yourself as gay or not but if you are I love it. Not enough gay gun enthusiasts out there.
I have a super 42 in my custom ggp 16" barreled AR-15. I don't like it very much. It twangs and has that noise I do not like. I'm about to replace it for a jp silent captured spring to get rid of the "twang" I do like the Geiselle Heavy Duty ACOG mount tho on it for my 4×32 green dual cross hair Trijicon ACOG
Wish I'd seen this before I dropped almost twice the $ on that JP captured spring 😅. Depending on how much I like it (once I eventually get my carbine built), I may end up getting one of these Super 42's and dropping the JP into my other rifle
Have the Geissele Super 42 and buffer on all my rifles. So far so good. Heard good things about the VLTOR A5 system as well. Lots of people recommend the VLTOR system as well.
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Privacy Overview
This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
This spring is trash. The spring is very quiet but not reliable. Takes a lot of metal off the buffer tube. You will have to clean your buffer tube after 300 rounds.
Dude, were you in the Navy?
when i put this in my weapon it thanked me ❤
Have you tried flat buffer springs and if so what do you think of them? What I like about them is they will work with any standard buffer.
Bravo.thenks
“ basically the same “ ? Except you have to use their proprietary buffer and it cost 60.00 dollars, compared to a spinco spring for 20.00 dollars and you have a choice of different spring strengths and they allow for any mail spec buffer 🤔
Is no one gonna point out that this man is clearly on meth AND his shirt says "something something METH"
I've read you can just buy the spring and it will work fine with most buffers. I'm installing it on a aero buffer this week. Fingers crossed lol
But my main point is the super 42 just kicks ass it has h1-3 it is such a good system it will last 10 times longer than your standard quality car being spring and as soon as you racket you’re like oh wow this was worth 70 bucks for an H2 and then I continue to Byam I have three RN and he’s a mind systems that will work great with it and you know it’s super it’s almost like is it it’s very very quiet especially when you released your boat for shooting suppressed subsonic that’s where it really really shines you get zero twang and the twang sort of makes guns even if they’re quality firearms and Mason feel shitty so I invest in longevity in the parts that I buy for the most part and do some R and D and the R&D is it on like the centurion barrel they cross pendant at the top because of how low profile there gas block was and they also have a notch that corresponds to the perfect spot in the barrel for it to sit over the gas port and then obviously it has set screws for if you’re such a growing one but when you buy it with the system pinned it’s worked phenomenally and it’s got a .061 carbine gas is from which is crane spec it’s about .0615 and that’s my barrel but they say it’s around .061 and .062 is crane spec for an M4 so with the barrels I purchase I have to focus on quality ammo and is the system going to cycle it properly without a suppressor so I might have to buy a H one which I’m fine with it’s what 60 bucks and if the H one doesn’t work for you you can always buy a $20 tungsten weight and add it to it as the system allows you to do that to change weights out I assume you need a kit punch kit Jordan still gotta figure that one out
But for example right now as it sits it’s a $4000 set up easily and on going to be ordering the SPS when they are back in stock every is your fire can is not in stock but the SPS is gonna be my first 30 Cal can dance backwards compatible which is cool and it’s a little bit longer than the RC two but I might throw down my 55 sixes just to Yosi but inevitably I’ll either be getting another share fire or if my left dominant side does not like it give in with the gas busting charging handle from Radian and I do use optic risers I put you in a better situational like for your body your muscular skeletal situation system and you have situational awareness around you more so than you would if you were sunk into the optic lake and ACOG that at absolute if you understand what I’m saying plus if you are wearing armor and you sync down into the gun you can easily get hit in between your arm or you could get hit in the neck thoracic area that gets exposed is in your chest in the boat will zip through you do not want it to zip through from your chest downward angle doing God knows what so my tip is shoot your rifle like the way you shoot your handgun the same fucking way if that means get an optic riser and a cheek riser so be it they make a shit ton of them through the CTR stocks bunch for the B5 a few different not many but I have an APE defense 1 inch cheek riser for the B5 stock and run the unity Holographic setup right now with that and it’s on a Ris two also with a $500 barrel but at least it a lot more bar stock and it’s full auto rated for continuous full auto basically an SAW barrel with a cold as COM profile and probably can be used on the AR if it isn’t already it’s double chrome lined CHF centurion arms another if you were looking to do a GWOT built I’d recommend there’s also as well as for that set up definitely but they have a few other modern profiles and shit and they have them profiled and house their CHF out sourced as well as the Florida bar stock that they get you might as well use the best if you can so also if you’re going to buy a barrel and you know the ball carrier if it’s nitrated or not if it’s a Phosphated one definitely get it head spaced you want consistent pressures on that chamber people and manufacturers fucking overlook it like it’s a plague but there are different you know tolerant scabs in the fucking barrel extension not everyone is the exact same so and especially when you polish the barrel M4 extensions you need to find the right bolts and these companies have tons and tons they just have to maybe route through 30 or 40 and then they find the right ones and that’s why it cost 60 bucks because they had to go through a whole shit ton of bolts and use a Go gauge and a non-go gauge
Definitely one of the reasons I got it is the longevity and staying true to the design there’s so many odd contraptions and they’re priced a lot more like the GPSPS but I feel like it’s too much to fuck with too much to fill around with for an AR platform I just throw in one of these and change it up depending on what system I’m running and run them on every single AR that I have it made it my 10.3 a dream to shoot just using a H2 42 bufffer and spring I did hear that it does fit on the VolTr A5 they make one for it sort of I don’t know I might be miss information or some thing I didn’t get but I’ve seen people use them on that system but I have three of them and the tolerance definitely plays affecting boat bounce and shit like that or around the spring there in the buffer you know that the ring that you get from it getting chewed up by the detent and I had that on some mil spec sort of receivers and most companies don’t take into affect super tight tolerances and what not and that’s where you get your performance for example my radian model one there is zero movement and the receiver said it’s kept the super 42 in beautiful shape I built it myself it has a DDC buffer also from them but it’s a 10.5 and I threw a dev Gru 416R ss 10.5 barrel and the receiver set together it’s a match like perfect even though I bought my lower a year ago I recently bought the upper rail and I probably should’ve done that from the start but you know I have multiple upper sector of the lower on But anyway by 10 three that thing zero movement with the H2 as I was talking about and super flat shooting a bit heavy the MK4 rail with a Daniel CHF barrel but I am happy with the new radio model homes built thermal fitbarrel
I've got a ruger 556 N s&w MP Sport 2 and I've been wondering should I replace the buffer spring an weight.
I have an ar pistol an it won’t cycle? Any ideas??
I’ve been trying the A5 tube, super 42 rifle length spring & BCM’s new buffer. Need more testing but so far so good.
FYI you can replace your spring with standard springs once a year for 22-25 years before you spend the amount that this costs. You’re welcome.
Really like the H1 Super Duty in my 16” mid length
Works great never go back to a regular spring.
Shot testing or comparison? I think a picture can explain its twisted wire.
Will this work good with a 50beowulf
I wanted to switch out my buffer and spring on my DDM4V7 just seems like my Daniel shoots a bit heavy so I’m thinking a good buffer and spring to calm that bolt down a bit I’m running the stock H buffer maybe a H2 anyone tried this spring and buffer on a DDM4V7 mid length gas system
Is the weight removable? I’ve got an H3
Just installed a Super 42 as a replacement for the OEM spring and buffer on the S&W Volunteer XV. Pretty much to mitigate that buffer spring twang and it made a huge difference. Won’t know how it will run til I get out to the range but so far this was a great upgrade.
Just picked up their tube/buffer/spring kit with a H1 buffer for my 18” BCM. I’ve had a fixed A2 stock on it for years and it’s worked great but my son is getting interested in shooting and i need an adjustable stock for him.
Will this spring (carbine length) work in any carbine length buffer tube? I have a complete m4e1 pistol lower
So in an ar10 308 , will it work ?
You do know that your poster "I'm your Huckleberry" is the term used in the mid 1800's for gays. Not sure if you are intendingt to out yourself as gay or not but if you are I love it. Not enough gay gun enthusiasts out there.
I have a super 42 in my custom ggp 16" barreled AR-15. I don't like it very much. It twangs and has that noise I do not like. I'm about to replace it for a jp silent captured spring to get rid of the "twang" I do like the Geiselle Heavy Duty ACOG mount tho on it for my 4×32 green dual cross hair Trijicon ACOG
I run the super 42 in everyone of my rifles. Your right, no more annoying twang when you shoot.
I just installed the geissele 42 with an h2 buffer in my rifle so far so good.
I'm running a VLTOR A5H2 on my 11.5 SOLGW and a Geissele Super 42 H2 on my 10.5 Radian Model 1. Both are outstanding systems.
Would this setup be good for a 16 inch mid length gas system with just the H1 buffer ? What do you think about this setup vs doing an A5 setup ?
Welp, adding it to my list of improvements once I put some more rounds through my "build".
Nice! Looks like a good setup.
Wish I'd seen this before I dropped almost twice the $ on that JP captured spring 😅. Depending on how much I like it (once I eventually get my carbine built), I may end up getting one of these Super 42's and dropping the JP into my other rifle
Quit making me spend more money 🤣
What I really like about the captured springs, other than the sound benefit, is that I don't need that damn buffer retainer pin
Have the Geissele Super 42 and buffer on all my rifles. So far so good. Heard good things about the VLTOR A5 system as well. Lots of people recommend the VLTOR system as well.
Great info, I’ve been thinking of replacing mine, with the one you tested. Thank you!
Or the buffer or the bolt carrier are short to proper spec.