Learn how to install your ODIN Works forend to your build in just minutes. It’s that easy!
Note to readers: Please click the share buttons above or below. Forward this article to your email lists. Crosspost on your blog site, social media, internet forums. etc.
Mines got alot of play back and forth on my ar10. Its torqued down, screws are in, but it still wiggles left to right bout 1/4in. I'm stumped. It looks great and is really light, but the height of the rail doesn't line up with my aero upper. Maybe I did it wrong, but I don't believe I did. Thinking of replacing with an aero handguard.
why wont standard ar torque wrench adapters fit the barrel nut?
Minecame with the barrel nut pinned inside the forend. How do I get it out??!!!!
Can you do another video for the newer 1 piece barrel nut adapter? It's pretty ridiculous that I can't find anything on the newer stuff!
Thank you need more of this in 2021
Would the odin works M-Lok forend 9.5" work with a spartan 9MM non-reciprocating side charge billet upper receiver w/ LRBHO? As for the barrel i'm going with the odin works 7.5" AR15 – 9MM barrel.
I've got ODIN Rune handguards on both my ARs and I love them. Really well designed and engineered and very easy to install.
To anyone watching, DO NOT install aluminum gas blocks ! They are weak and begin to fall apart at the drill holes after a couple of hundred rounds.
This system sucks. There was a tiny bit of slop in the way the pin fit into the gas tube hole on the upper, and that made it so the handguard wouldn’t time properly. Had to overtighten the barrel nut, and then back it off a little bit to get it to time right. Now I’m not certain that the barrel nut is torqued to the proper spec.
Shitty.
Well thought out
Very nice
is the barrel nut basically just the threads on the receiver?
Is torque pounds the same for your 9mm barrel? I am REALLY hoping your O2 Lite forend fits on a Spikes 9mm upper. I want to show off my Odin stainless steel barrel. The spikes upper has a raised point in front of the ejection port door that keeps some forends from fitting.
I'm 15 minutes away from installing this my only concern is the barrel nut timing my ragna barrel nut has 4 flats that the screws are suppose to line up with, when you just hand tightened your barrel nut for the video the timing was way off, to give proper hand guard screw placement do you have any tips to make sure the barrel nut flats line up with the hand guard screws or does it matter if half the screws are on the flats and half are on the round portion of the barrel nut and will this cause the screws (after being tightened) to have half to stick out of the hand guard and half flush? thanks P.S. I will follow up on this question when I start and finish the install in an hour
O2 lite is best forend money can buy, unparalleled weight and looks. Unfortunately aluminum forend adapter vs 6 steel screws, had to order replacement adapter since threads are ripped on.
What's the inner diameter?
Can you offer AK parts? lol
Does the O2 lite handguards have anti-rotational tabs?
What handguard was installed on this video ??
I also have a superlative arms piston conversion kit and will be running the O2 lite, can you email me the photos of the mod to the barrel nut? Email to chris.wetch@hotmail.com
Love my hand guard & my barrel from you guys👍🏽
Would this forend work with an Adams Arms XLP piston system?
Do you know if this forend will work with the superlative arms piston conversion? I love the look of this forend but DI is a no go for me and I'm not sure if their gas block will be low profile enough
I’m returning your MLOK rail I purchased.. it wasn’t even deburred and the serrations are like razors… absolutely piss poor
I have same timing probs…i tore the box so now i m stuck with it .
I tried one of these last year on a .308 MEGA billet upper. I could not get the fore-end to time correctly. I contacted Odinworks for help, and never heard a word back from them. Fortunately the dealer (Primary Arms) let me return it.