Note to readers: Please click the share buttons above or below. Forward this article to your email lists. Crosspost on your blog site, social media, internet forums. etc.
Good video but rehearse a minimum of one time before recording for keeps…do a dry run and make your presentations short and sweet. Remember, you're taking up my time to watch them and that is something I will never get back. This would have been a 5 star video otherwise..as is, it's a 3.
this video is like idk sa 4mins way to long. we didn't need the whole life story. , just show the 30secs it shows everyone how to install. not hating just saying
ATTENTION ALL MAGPUL CTR & MOE OWNERS WHO ARE LOOKING TO PIN YOUR STOCK:
Zero cost, drill one hole, its that simple. Just remove the roll pin holding the plunger assembly. Remove spring and cross bar. Re-insert plunger into stock attached to buffer tube and position length to where you want to pin. Rotate plunger 90 degrees, to where a pre-drilled hole at bottom of plunger lines up to any side of stocks roll pin hole, re-insert pin and firmly tap the roll pin to hold plunger in place. Flip the stock over and use a 3/32 drill bit inserted into the roll pin hole to drill hole into the other side of the plunger. Once hole is drilled, remove roll pin from other side and tap roll pin into the hole just drilled to pin plunger in place. You're done.
Worst case scenario buy a new roll pin (3/32 x 3/4) @ $.50 – $.60.
Thanks for this, it's exactly what I needed. I'm new to the AR15 world too, but the factory stock on mine kills my shoulder. This will be an awesome upgrade!
you know when you've been messing with something and trying to figure it out only to feel like an idiot when you find the video that shows you what you were doing wrong?
That was me, trying to remove my stock from my M&P Sport AR to put on a sling mount. I'm trying to unscrew that which holds the adjustment lever on, never thought it'd flip out duh.
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Privacy Overview
This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
สวยงามมาก😁😁ขอพันท้ายสักชิ้นได้ใหมครับ😀😀
Really because it's tearing up mg fingers
This video should be half the length it is. Collect your thoughts beforehand a bit, perhaps.
My buffer tube doesn't have the rail under it. Will mine still go on
great video! thank you!
Dude! Get out! Your house is on fire!
Great vid. Thanks for the info!
Dude some constructive criticism. Waaaay tooo long. Just get to the point. Your Rambling. Otherwise, good try.
Good video but rehearse a minimum of one time before recording for keeps…do a dry run and make your presentations short and sweet. Remember, you're taking up my time to watch them and that is something I will never get back. This would have been a 5 star video otherwise..as is, it's a 3.
I want to get the ctr will it fit on all ar15
Skip to 3:40 to see how to install the stock.
$80!?!?! Holy shit that's double what they go for bro
Man!! Phew!! Just got mine delivered and didn't no there is a difference so glad I got the right one. Good video thanks
this video is like idk sa 4mins way to long. we didn't need the whole life story. , just show the 30secs it shows everyone how to install. not hating just saying
Good video lol I was struggling heavy to get it on and I was if this guy can do it while holding a camera I can do it hahaha
I ordered a Mil-Spec stock just out of random, and i just checked, and my buffer tube is a Mil-Spec lol (sweating like crazy)
stfu and just install it
Good info =)
where can i get the buffer tube and stuff for this stock?
Thank you very much. This video helped a lot <3
thx got the info. was worry I got the wrong one
ATTENTION ALL MAGPUL CTR & MOE OWNERS WHO ARE LOOKING TO PIN YOUR STOCK:
Zero cost, drill one hole, its that simple. Just remove the roll pin holding the plunger assembly. Remove spring and cross bar. Re-insert plunger into stock attached to buffer tube and position length to where you want to pin. Rotate plunger 90 degrees, to where a pre-drilled hole at bottom of plunger lines up to any side of stocks roll pin hole, re-insert pin and firmly tap the roll pin to hold plunger in place. Flip the stock over and use a 3/32 drill bit inserted into the roll pin hole to drill hole into the other side of the plunger. Once hole is drilled, remove roll pin from other side and tap roll pin into the hole just drilled to pin plunger in place. You're done.
Worst case scenario buy a new roll pin (3/32 x 3/4) @ $.50 – $.60.
.
Is this stock worth it compared to the moe? Also, why should I change from my original stock
Great video on how to change out the ar15 stock ,thank you
Very helpful. Thanks
Thanks My Brother in Arms.
Thanks for this, it's exactly what I needed. I'm new to the AR15 world too, but the factory stock on mine kills my shoulder. This will be an awesome upgrade!
The flag on your mag well is backwards….nice set up
does it matter if the castle nut is not aligned with he charging handle?
Pro tip: NEVER let youtube fix your video, it will tear or warp your footage.
what kind of optics are you using?
the word "UM" is said 376 times in this video. Um okay
Holy shit just put it on
you know when you've been messing with something and trying to figure it out only to feel like an idiot when you find the video that shows you what you were doing wrong?
That was me, trying to remove my stock from my M&P Sport AR to put on a sling mount. I'm trying to unscrew that which holds the adjustment lever on, never thought it'd flip out duh.
Thanks for sharing.
Could I use this same concept on an airsoft gun?
Please no hate
Thx that helped me perfectly
Thx that helped me perfectly
*on fire. Lol
Dude, your neighbor's house is in fire.
Would I have to get a new buffer tube if I put this on my PA 15?
I want to put this on a 20 inch barrel rifle. Take off the A2 butt stcok and replace it with this one. Should work right?
Very helpful. Thanks!