StrikeIndustries.com
StrikeIndustries.com/shop/ar-aludc-223.html
Music:
soundcloud.com/thetempleofsteve
Support my Channel on Patreon:
Patreon.com/OreGear
Check me out on social media:
OreGear on Instagram
Facebook.com/OreGear
OreGear.com
StrikeIndustries.com
StrikeIndustries.com/shop/ar-aludc-223.html
Music:
soundcloud.com/thetempleofsteve
Support my Channel on Patreon:
Patreon.com/OreGear
Check me out on social media:
OreGear on Instagram
Facebook.com/OreGear
OreGear.com
Angled end of spring pops out on me every time Dust cover closes and opens.
Thank good sir! Jaut bought a used ar10 and dust cover wasn't working properly. I know why now and fixed it that's to your video
Thankyou especially on spring instruction
I dont understand why mine doesn't close
Can't get mine to close
Love it
Nice that it has those bumpers. That way you don’t hear the dust cover when you fire a round
Found out the hard way that they only work 50% of the time. Looks good but don’t work properly. Stay stock
it's what i use on my ar builds my husband showed me and this girl is in love
Sure, super easy when you have that type, with the detent. I have never seen one like that before. I just installed my first one today, and it was a PAIN! Had to remove that tiny "C-ring" from the pin, then remove it while holding the spring so it wouldn't fly off, then once I got the pin started into the new cover (and the spring), I fed it back through, and also had to twist the spring on the "long end" so it would have the proper tension. After I got it fed back through the holes, I had to put that tiny "C-ring" back in place, using tweezers, a small flathead screwdriver and small hammer. This would be a DREAM for me!! I need to look into getting this style! The easier, the better!!👍
Those things are crap and dont latch properly
why is your scope bridged
Thanks!
"Ultimate dust cover" is a stretch. If you want something that looks different then that's fine, but the marketing is gimmicky.
Very sexy Mid West set up, loving the build good sir. I don’t know why your vid would get a thumbs down must be those who don’t have style lol very well made video and instruction on installing this product. Just got mine today so now I’m excited to install, hope you and yours are staying safe and healthy during these crazy times.
These dust covers have a bad spring detent design and it will put premature wear on your upper receiver…….Mil-spec is designed to last and are just as easy if you take the time to learn…..
Mil-spec dust covers…..Don't be fooled by Strike Industries or any other snake oil designs……These are just for lazy people without proper gunsmithing skills……These dust covers suck!!!!!!!…..Mil-spec for a reason……
those cover are easy to install and gives it a different look than mil-spec
First up, why is your optic so far forward, half on the receiver and half on the non monolithic rail? How are you getting eye relief?? It doesn't look like you're buying junk equipment but you are putting your things together like you are someone who does buy junk equipment…
With that being said I had a Strike Industries dust cover and forward assist installed in a nice upper I won. Both parts failed and broke. Junk imo, too bad bc the aesthetic is good.
Yep I have them on everyone!!!!
Why won't this work on an aero m4e1?
So the tabs keep the dust cover quiet when the dust cover swings open when you FIRE A BULLET? lol
Why can't people stay in view while demonstrating how to videos . Smmfh
Mine won’t fucking shut this thing sucks
Thanks for the help!
Awesome video. I watched a different video and it didn't tell you to give more tension to the spring.
why didnt u make the video taking of the old dust cover smh ? that would be a more informative video
Why change dust covers? 🤨
That's slick! I just built my first upper and that little c clip on the GI was a b*tch!
Glad I watched your video, adjusting the detent was super helpful.. Since SI doesn't ship any instructions I had no way of knowing the ball detent that keeps the door closed is adjustable. Good Video. Thanks!
Holy shit! Fuck…… and I thought I was done buy shit for my ar's………. after messin with a dozen or more old school covers this was a well thought out piece of kit, sooo many damn C clamp washers lost and sweatin over!
Great info thank you
Ball bearing detent isn't strong enough, doesn't stay closed.
this is a great dust cover BUT the only problem is it wont fit on the Aero Precision M4E1 upper
Dang man you got to love Strike Industries! Great Video👍
Nice video, but one thing you didnt do is to uninstall the stock dust cover.
Nice dust cover
This thing SUCKS!!!!! Doesn't stay closed even after adjusting. The rubber pads DO NOTHING, they dont even contact anything at all.
lol at final resting place..
Nice!
I did it! 😬