Easy DIY AR15 Upper and Lower Wobble Fix. This is a VLTOR upper and a PSA lower and just shows how to fix a wobble or slop if needed.
►TAKE A LOOK AT THE HUNTING PRODUCTS THAT I USE:
►CHECK OUT MY CAMERA GEAR & EQUIPMENT THAT I USE:
*The above links are Amazon affiliate and affiliate links*
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
►►► ADD ME ON ALL SOCIAL MEDIA ◄◄◄
► INSTAGRAM:
► TWITTER:
► FACEBOOK:
►EMAIL: wellsj54@gmail.com
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
►►► PLAYLISTS ◄◄◄
►COYOTE SEASON 2019/2020:
►COYOTE HUNTING GEAR & SETUP:
►DEER HUNTING:
►RUGER AMERICAN BUILD SERIES:
►BEAVER HUNTING:
►RIFLE INFORMATION SERIES:
►SHED HUNTING:
►HUNTING & OUTDOOR VIDEOS:
►PRODUCT REVIEWS:
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
Music provided from:
www.youtube.com
Thanks for watching!
Note to readers: Please click the share buttons above or below. Forward this article to your email lists. Crosspost on your blog site, social media, internet forums. etc.
#7 or 3/8” o-ring should do it. Be sure to subscribe to see more 👍
This "fix" is going to make it worse. In other words, because of the tension you added the pivot and possible the takedown pin holes will oval out and now you'll have real problems. You better buy o-rings in increasing sizes lol
I like that handrail. Would that fit an adams arms piston kit?
Awesome. Thank you!
How do you feel about adding the o ring to the front and possibly bedding the rear lug?
Play is fine all important action is happening in the upper. Lower does nothing to increase accuracy by much unless you're really into shooting 1000 yard targets then u might wanna look for tighter fit components. If your main objective is self defense 5 to 200/300 yards slop is fine.
Thank you. Great Idea= Great fix
Your awesome thank you man!!!
Wow.. nice video ran across your 12.5 grendel build and you gave information about this in the video.. very informative thanx for the great video and information… 👍🏾
Brilliant idea, thanks.
What size O-ring?
What size o ring?
Great video need to do this to my carbon15 bushmaster. Got a little wiggling
MY AR has a gap between the upper and lower I can fit a sheet of paper in, this is normal right?
I just bought my PSA 10.5 556 ar pistol n I tell yall, it wobbles too. I move the gun up n down and I can clearly hear something is moving back n fourth in the receiver. So I dont even know what to do probably send it back or whatsoever
I have a BCM upper with this very problem.. Thanks for the awesome video.
Does the wobble even matter?
I have a micro AR with micro buffer tube side charging handle when I take the rear takedown pin out I'm able to charge AR properly but with pins intact BCG WILL not slide back all the way do you have a fix for that
Great fix, usually the simple fix is the best… Appreciate you sharing.
What size (diameter) o-ring do you use? I'm guessing 3/8"
If you put the gun in a block vise and wiggle it will show up on video much better. Just looked like you were moving the entire gun both upper and lower moving together I know there was slop but could not really see it.
This makes far too much sense. Excellent fix.
As most have said, Thanks! Wish you were here to Zero in the 2 scopes (3-9×32, Reflective and Laser), i'm having a tough time doing it even with a bore laser sight (I do have them close, but close isn't good enough) <—I'm a n00b.