Start to finish assembly of glock 19 slide.
Thank you all for watching and leave a like….(or dislike) so I know how good or bad my video was and whatever’s on your mind leave it in the comments.
Twitter:
instgram:
If you like my videos and feel like pitching in a bit to help fund future videos:
Note to readers: Please click the share buttons above or below. Forward this article to your email lists. Crosspost on your blog site, social media, internet forums. etc.
Thank you for the video, you made it short and to the point! Got my slide assembled perfectly!
You could use a toothpick for the slide plate part 🤘🤘
Nice weapon
Question…Why can't you put a couple of drops of oil on the channel liner,,not a lot ,,just a tad so it will slip in easier??
Where you buy the slide at ?
My sister told me she got a safety gun for reliable seller glockworld on wickr now I got from him thanks man.
You realize you shouldn't have to use a hammer with the channel liner right?
2:07 one of my little pieces shot away when trying to install cannot find it anywhere please tell me i dont have to buy a whole new build kit… is there anyway i can just buy that piece again
I'm stuck on the first part lol
Did it wrong dont watch
Someone I knew used a paper mate pen to insert the channel liner sleeve. It fits perfectly and no hammering just easy push right until it stops. No forcing, no special tools.
Guys I got the new glock with switches from mrmasterglock I contacted them on * wickr me* the stuff is really good you can try them..
Watching this guy ramble on is fucking boring as shit.
"And we'll take our rod guy and get it matched up there". Thanks i know nothing about these parts now.
I need help is there a email I can contact you
I spent $15 on a channel liner tool, only to find out my upper parts kit came with a cheap plastic one. Then I put the liner in the freezer for 10 minutes and it went in like throwing a hot dog down a hallway. Didn't even need the tool lol
List of the things i need?
Great tutorial.. vary basic. Boring not thrills… but quality for learning!
What size of lag bolt? 3/8, 5/16 or smaller?
really u skiped over the opnly part that is hard asf how did u get that cover on dude fuck
EXCELLENT INSTRUCTIONS!! I especially agree with the order of your steps! I grew up around rifles of every sort, as half of my family are all deer hunters in Northern Minnesota. I’ve never had any firearm completely broken down to all of its components, but your demonstration immediately alleviated any doubts that I had before I found your video! THANKS FOR SHARING!!
Im grateful for the knowledge in the video, once I committed to using it to put my slide together I did so. But buddy, your voice is boring to the point of painful. Put some confidence in it!! You obviously have assembled I have no doubt but you sound like a knitting vid, buck up or get out this is the last generation of legal home firearm manufacturing, grow some balls if you are arming patriots.
Where could I purchase this whole kit
Thank you for making this video. Without this, I would've screwed up the channel liner for sure. Glad I bought the tool immediately after watching this the first time.
Thank you for the video. My slide came with the channel liner installed. Yay! All the rest went together pretty smoothly except for those two little retainers. UGH!
For anyone this concerns, make sure to download these videos
How is this aim kit? Quality? Crap?
Bruh I'm having so much trouble with putting the back plate, that extractor spring is hard as hell to push down
Need to remove a channel liner, what size lag bolt..? Great video by the way!
Ive never needed to use a hammer to push the liner in.
that tiny black pin got spring-propelled out of existence. I dont even know what those are called. if i did, i'd order a bulk replacement.
Rts
Does anyone know what chemicals go into the casting of the polymers in the frame?
Thanks in advance.
Mr SNS
i can’t do the first step lmaooo
For the liner install I used a Ticonderoga no2 pencil, eraser side with full unused eraser worked like a dream and gun shoots no issues…oh don’t sharpen pencil. Trolls 🖕🏿
What slide parts did you use? I'm looking for a oem glock one but it's hard to find and I was going to opt out for a brownells slide parts kit.
Just got me a rock slide great info
I needed this very much
I cant get my extractor plunger to go down and i cant get my backplate on. Its stupid issue but an issue nonetheless
Bro the spring on the plunger the back plate does not compress down what's up with that..need help u make it look to easy
This is by far the best channel for building 80s or assembling glocks. Easy to follow. Step by Step. Simple directions. Thanks so much man. I personally appreciate it.
hey heads up its a felony to have a threaded barrel on a pistol in California.. i didn't know either until I built my first p80… threaded barrel makes it an "assault weapon" as per the dipshit doj
Spare the whack and spoil the slide. Good vid man, enjoyed it w bourbon in my basement. Thanks and Merry Christmas
its wierd how hard you have to hit the liner. I installed mines today with no tools, and i was able to push it down with the tip of the firing pin.